FOUR BRANDS. ONE BENCH. EVERY BLADE WE SHARPEN.
Freud, Diablo, Tenryu and Popular Tools carbide saw blades, side by side, with one set of specs. Filter by your saw, your cut and your material, then send them back to us when they dull.
THE LINES WE STAND BEHIND
These are the blades that cross our sharpening bench every week. We stock them because they come back sharp, again and again.
Industrial precision. Italian made.
TiCo Hi-Density carbide, laser-cut anti-vibration plates and Perma-Shield coating. Freud is the professional woodworker’s benchmark for ripping, crosscutting, panel sizing and laminate.
Jobsite tough.
Framing, fine finish, Steel Demon metal cutting and track saw blades built for circular, miter and cordless saws on the job.
Japanese steel. Silent, smooth cuts.
Micro-grain carbide on hand-tensioned plates from Japan. Power Blade, Silencer, Gold Medal, Rapid-Cut, Alumi-Cut and Steel-Pro series for wood, laminate, aluminum and steel.
Industrial blades, sold only through sharpeners.
Nearly 900 order IDs in 45 series from San Antonio, Texas: general purpose, combination, rip, panel, scoring, non-ferrous, truss and dado. Priced 2% below list and shipped from Popular’s U.S. warehouses.
YOUR NEXT CUT STARTS HERE
THE COMPLETE COLLECTION
Four brands. One set of specs. Filter by what you cut, what you run and what fits.
A LITTLE KNOW-HOW. A BETTER CUT.
Start with the saw. Then the cut. Then the material. The blade picks itself.
01 / DIAMETER & ARBOR
Read the diameter and arbor off your old blade or the saw’s plate. 7-1/4" with a 5/8" knockout is the circular saw standard; 10" or 12" with a 5/8" or 1" bore covers most table and miter saws; European sliders run 30mm.
02 / TOOTH COUNT
24T rips solid stock with the grain. 40–50T is the general purpose and combination range. 60–80T crosscuts trim and plywood. 80–120T leaves melamine, laminate and aluminum chip-free.
03 / GRIND & HOOK
ATB shears wood cleanly; FTG rips; TCG survives laminate, plastics and non-ferrous metal; Hi-ATB is the chip-free finish grind. A negative hook keeps a sliding miter or radial arm saw from climbing the cut.
04 / KEEP IT SHARP
Every blade here can come back to our CNC sharpening shop in Cape Coral, in person or by mail, and be ground back to its original geometry many times over.
BUY IT HERE.THE OTHER HALF OF THE SHOP
We sharpen carbide saw blades on CNC grinders in Cape Coral and take blades by mail from every state. Buy the blade here, run it hard, send it back: we grind it to the original geometry so it cuts like the day it arrived.
STRAIGHT ANSWERS
Two numbers: the blade diameter and the arbor (bore). Both are printed on your current blade and in the saw’s manual. Most table saws and 10" miter saws take a 10" blade with a 5/8" arbor; 12" miter saws take 12" × 1"; corded and cordless circular saws take 7-1/4" × 5/8" with a diamond knockout; European sliding table saws take 30mm bores with pinholes. Filter this shop by diameter and arbor and every blade shown will fit.
Fewer teeth cut faster and clear chips better; more teeth leave a smoother edge. Use 24 teeth for ripping solid wood, 40–50 for general purpose and combination work, 60–80 for crosscutting trim and plywood, and 80–120 for melamine, laminate, veneer and aluminum.
ATB (alternate top bevel) teeth shear fibres for clean crosscuts in wood. FTG (flat top grind) teeth chisel through ripping cuts. TCG (triple chip grind) alternates a chamfered tooth with a flat raker and stands up to laminate, plastics and non-ferrous metal. Hi-ATB uses a steeper bevel for chip-free cuts in melamine and veneered plywood. ATB+R combination blades mix bevel teeth with a raker so one blade rips and crosscuts.
Freud, Diablo and Tenryu blades are stocked in our catalog and go straight into your shopping cart. Popular Tools blades ship direct from Popular’s U.S. warehouses and are ordered through their own order box on this page; they check out separately. Both orders come from the same family-owned shop in Cape Coral, Florida.
Yes. Family Hardware runs a CNC carbide saw blade sharpening service in Cape Coral with mail-in service nationwide, and free shipping both ways on 10 or more blades. Every blade in this shop can be sharpened back to its original geometry.
Kerf is the width of the cut. Thin kerf blades (under .100") remove less material, so they need less power: the right choice for contractor table saws, cordless circular saws and anyone trying to save stock. Full kerf blades (.100" and up) run truer on high-horsepower cabinet saws and industrial machines.
Aluminum, brass and other non-ferrous metals want a triple chip grind with a negative hook angle, such as Tenryu Alumi-Cut, Freud non-ferrous blades or Popular Tools non-ferrous series. Steel needs a dedicated ferrous blade for a dry-cut metal saw, such as Diablo Steel Demon or Tenryu Steel-Pro. Never run a wood blade in metal.
Customer Service
Contact Us
Returns
Shipping & Tracking
Gift Card Balance
Rewards
Promotions
Credit Application
Locations
Cape Coral
Fort Myers
All Store Locations
Grills
Grill Store — All Grills
Alfa Pizza Ovens
Big Green Egg
Napoleon
Challenger Designs
Delta Heat
Tagwood BBQ
Twin Eagles
Replacement Parts
Warranty
Services
All Services
Saw Blade Sharpening
Saw Blade Shop
Key Cutting
Screen Repair
Propane Exchange
Lamp Repair
Key Fob Batteries
Freud
Lamello P-System
Popular Tools Saw Blades
Diablo
Tenryu
© 2026 Family Hardware. Family Hardware and the Family Hardware logo are registered trademarks of Family Hardware Corporation. All rights reserved.
